Skip to product information
1 of 1

BAESA COLORS PAINT CENTER

A-Plus Procrete® Epoxy Tank Lining White 4L

A-Plus Procrete® Epoxy Tank Lining White 4L

Regular price ₱3,800.00 PHP
Regular price Sale price ₱3,800.00 PHP
Sale Sold out

A-Plus Procrete® Epoxy Tank Lining is a thermosetting heavy-duty construction epoxy specially designed for storage tank applications. It is a water impermeable non-toxic coating that cures to an abrasion and chemical resistant barrier which makes it safely protect and maintain optimum storage tank conditions. This product is highly suitable for properly prepared substrates such as concrete and steel.

 100% Solids Construction Epoxy Membrane
 Cures to an Extremely Tough, Hard, and Durable Reinforcing Material
 Superior Chemical Resistance (Solvents, Oils, Acids)
 Superior Adhesion and Does Not Shrink
 Fast Curing, Easy Workability, Wide Range of Application
 Non-Toxic, Food Grade, Lead-Free
 Ideal for Concrete and Steel Surfaces

 

SPECIFICATIONS:

Principal Uses: For interior surfaces of concrete and steel tanks for storing water, chemicals (except high concentration acids), agricultural products, powders, and other liquids.

Sheen: Gloss

Coverage: 20-25 sqm per gallon / coat

Surface Dry: 4-6 hours

Recoat Interval: 4-6 hours

Dry Through: Full cure within 7 days

Thinning: A-Plus® PG Epoxy Reducer

Clean-up Solvent: A-Plus® PG Epoxy Reducer

Application: Brush, Roller, Spray

Packaging: 4L

Pot life: 30 mins – 1 hour Available in Clear, White

 

SURFACE PREPARATIONS AND PRECAUTIONS:

Precautions:

    1. Mix only enough paint for use in one session or paint job.
    2. Excess mixture that are not used up will gel within the day.
    3. Do not put mixed components back into its original container.
    4. Avoid painting under extreme environmental conditions and/ or bad weather conditions.
    5. Not suitable for surface temperature conditions below 10 deg C or beyond 100 deg C.

Surface Preparation:

For Metal Surfaces:

    1. Remove dust, dirt, grease, oil, wax and other foreign matter using a rag soaked in paint thinner.
    2. For repainting, use a mechanical grinder or A-Plus Supertanggal® Paint Remover to strip off old paint film to bare substrate then remove oil and grease by solvent cleaning followed by scuff sanding. To remove rust, wire brush or strip affected areas after treating with A-Plus® Rust Converter. Let it sit for 10 – 15 minutes before washing off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately upon drying of the surface before rust sets in.

For Concrete Surfaces:

    1. Ensure proper surface preparation by removing any oil and dirt by detergent cleaning.
    2. Roughen surface by scuff sanding to enhance paint grip and adhesion. If necessary, use mechanical tools such as a planetary grinder for uneven surfaces.
    3. Rinse the concrete thoroughly with water to wash away residues that could affect paint adhesion. Allow ample time for the concrete surface to dry.
    4. To repair large concrete surface imperfections, use either of the following:

– A-Plus Procrete® Low Viscosity Construction Epoxy – used for patching medium-sized concrete imperfections covering a large area.

– A-Plus Procrete® High Viscosity Construction Epoxy – used for patching larger-sized concrete imperfections covering smaller areas.

 

PAINTING PROCEDURE:

Mixing Direction:

    1. Stir and shake both components separately before mixing together.
    2. Slowly add the hardener to the paint while mixing slowly and thoroughly for 5-10 minutes before application. For better mixing, transfer both components to a larger container. Mixing ratio: 3:1 by volume paint and catalyst, respectively.
    3. For maximum performance, allow at least 10-15 minutes induction period of mixture before using. Mix just enough for use on one working session.
    4. WARNING! Pot life of mixed Paint and Hardener is 1 hour at room temperature.
    5. If necessary, thin down minimally with A-Plus® PG Epoxy Reducer.
    6. MIX WELL BEFORE USING.

For Metal and Wooden Surfaces:

    1. Primer: Apply at least 1-2 coats of Glazer Galva-Plus® Epoxy Primer. Let dry 4 hours to overnight. To ensure good intercoat adhesion, apply topcoat within 3 days after priming.
    2. Putty:To fix minor surface imperfections, use A-Plus A&B® Non Sag Epoxy Adhesive. Sand smooth before applying topcoat.
    3. Topcoat: Apply at least 2 coats of A-Plus Procrete® Epoxy Tank Lining over the well-primed surface. Allow at least 4-6 hours before recoating.

For Concrete Surfaces:

    1. Ensure proper surface preparation and waterproofing.
    2. Primer: Apply at least 1-2 coats of Glazer Galva-Plus® Epoxy Primer using either a brush/roller. Let dry overnight. To ensure good intercoat adhesion, apply topcoat within 3 days after priming.
    3. Putty: To fix minor surface imperfections, use A-Plus A&B® Non Sag Epoxy Adhesive. Sand smooth before applying topcoat.
    4. Topcoat: Apply at least 2 coats of A-Plus Procrete® Epoxy Tank Lining over the well-primed concrete. Allow at least 4-6 hours before recoating.


View full details